Features & Benefits

---

• IDEAL FOR: Repair, seal and fill non-structural cracks in concrete, masonry, wood and more
• SEALS (Textured): Concrete, masonry, stucco, wood, brick, drywall, cement Board, glass, aluminum
  (Smooth): Concrete, masonry, stucco, wood, brick, aluminum and galvanized steel
• Interior & exterior use
• Paintable
• Excellent adhesion
• Flexible seal
• Permanently repairs cracks
• Brush and knife grades

Application Guidelines

---

• Application Temperature: Above 40°F (4°C)
• Service Temperature Range: 0°F to 160°F (-18°C to 71°C)
• Method of Application: Knife Grade Trowel or putty knife
  Brush Grade Brush
• Working Time: Textured Knife Approximately 15 minutes for 1/4" thickness
  Textured Brush Approximately 30 minutes for 1/16" thickness
  Smooth Knife Approximately 30 minutes for 1/4" thickness
  Smooth Brush Approximately 30 minutes for a 1/16” thickness
• Application Directions: Knife Grade For small cracks below 1/32” 1. Surfaces must be clean and free of any material that may prevent adequate adhesion. Allow new concrete to cure for 30 days before application. 2. With a putty knife or trowel, fill the crack with TitePatch to a 1/16” wet film thickness. 3. Feather out the product down to the substrate itself about 2” on either side of the crack to blend with the substrate and aid elongation.
  For large cracks above 1/32” 1. Allow new concrete to cure for 30 days before application. 2. Cut out joint to about 1/4” wide and 1/4” deep. Surfaces must be clean and free of any material that may prevent adequate adhesion. It is highly recommended to use bond breaker tape to prevent 3-sided adhesion. 3. To allow for shrinkage, use a putty knife or trowel to slightly overfill the crack with TitePatch, forming a slight curve of TitePatch above the cracked surface. 4. Allow product to dry for a minimum of 4 hours, then apply a 1/16” wet film thickness over the filled crack. 5. Feather out the product down to the substrate itself about 2” on either side of the crack to blend with the substrate and aid elongation. It is the sole responsibility of the user to thoroughly test any proposed use with all substrates to determine project suitability.
• Application Directions: Brush Grade 1. Surfaces must be clean and free of any material that may prevent adequate adhesion. Allow new concrete to cure for 30 days before application. 2. With a brush or knife, apply TitePatch to bridge the hairline crack (< 1/64”) with a 1/16” wet film thickness at the center. 3. Feather out the product down to the substrate itself about 2” on either side of the crack to blend with the substrate and aid elongation. It is the sole responsibility of the user to thoroughly test any proposed use with all substrates to determine project suitability.
• Painting: Patching compound should be dry to the touch and ready to paint in 30 to 60 minutes, depending on SKU, with a water-based (latex) paint that does not contain plasticizer. For other paint types, a compatibility test is recommended.
• Cleanup: Clean uncured material or tools with water. After curing, excess material must be cut or scraped away.

Physical Properties

---

• Type: Latex
• Calculated VOC: <50 g/L
• Solids: Textured Knife 72%
  Textured Brush 77%
  Smooth Knife 79%
  Smooth Brush79%
• Flashpoint: Solvent free/Not applicable
• Viscosity: Textured Knife 120,000 - 160,000 cps
  Textured Brush 99,000 - 220,000 cps
  Smooth Knife 95,000 - 140,000 cps
  Smooth Brush 170,000 - 230,000 cps
• Freeze / Thaw Stability: Stable
• Storage Life: 24 months in a dry location at or below 75°F

Limitations

---

Not designed for continuous submersion or use below the waterline. Do not use on structural cracks or repairs. Product is not sandable. Air, patching compound and surface temperature should be above 40°F. Do not apply if rain is expected within 12 hours. Cure time is dependent upon ambient conditions including temperature and humidity. Patching compound should be dry to the touch and ready to paint in 30 to 60 minutes, depending on SKU, with a water-based (latex) paint that does not contain plasticizer. For other paint types, a compatibility test is recommended. For best results, store in a dry location at or below 75°F. For questions, please call our Help Line at 1.800.347.4583 or visit us at Titebond.com.

Product SKUs

---

Part Number	UPC	Case UPC	Size	Weight	Units Per Package	Packages Per Pallet	Color
5355	037083053555	10037083053552	1 Quart Pail - Smooth Knife	21.23	6	90
5356	037083053562	10037083053569	1 Gallon Pail - Smooth Knife	55.45	4	30
5365	037083053654	10037083053651	1 Quart Pail - Textured Brush	16.43	6	90
5366	037083053661	10037083053668	1 Gallon Pail - Textured Brush	42.65	4	30
5375	037083053753	10037083053750	1 Quart Pail - Textured Knife	18.44	6	90
5376	037083053760	10037083053767	1 Gallon Pail – Textured Knife	47.99	4	30
5385	037083053852	10037083053859	1 Quart Pail - Smooth Brush	19.64	6	90
5386	037083053869	10037083053866	1 Gallon Pail – Smooth Brush	51.21	4	30

Warranty Statement

---

Liability is limited to product replacement only.

---

Important Notice: Our recommendations, if any, for the use of this product are based on tests believed to be reliable. Since the use of this product is beyond the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or effects incidental to such use, handling or possession or the results to be obtained, whether in accordance with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore. Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict with existing laws and/or patents covering any material or use.

---

2020 Bruck Street, Columbus, Ohio 43207
CUSTOMER SERVICE 1-800-669-4583
TECH SERVICE 1-800-347-4583
www.titebond.com