Titebond on Facebook Titebond on You Tube MSDS
Loading

Titebond Concrete Primer


Titebond Concrete Primer is used over Gyp-Crete and lightweight concrete to provide a bondable surface for the installation of hardwood floors. It also performs exceptionally well as an additive to cement based patching and leveling compounds used over uneven or damaged subfloors. It provides adhesion of these compounds to concrete, wood, tile and other sound floor coverings.

When added to portland cement and a sand mixture, Titebond Concrete Primer enhances the bonding of new, wet stucco or concrete to old concrete, masonry, stucco and similar surfaces. It provides a highly water-resistant and resilient base.

Click for an instructional video about application of concrete primer.

  • Ready-to-use form

  • Acrylic formula

Type: Modified acrylic Weight Per Gallon : 8.6 lbs. Calculated VOC: < 4 g/L State : Liquid Solids : > 28% Flashpoint : > 200°F Viscosity : Very thin liquid Freeze/thaw Stability : Passes 5 cycles at 0°F pH : 9.5 Storage Life : 12 months in tightly closed containers at 75°
Application Temperature

40°F to 100°F


Service Temperature Range

-30°F to 200°F


Method of Application

Apply mixture with masonry tools to level and fill voids in the old surface. Use a squeegee for sealing concrete.


Application Directions

All surfaces must be free from dust, dirt, oil, grease and wax.
Add 2½ gallons of Titebond Concrete Primer to a 94 lb. bag of portland cement and three equal parts of sand. To a pre-mixed 80lb. bag of cement and sand or aggregate, add 2 quarts of Primer. For smaller amounts, reduce the amount of Primer in proportion; to 40 lbs. of dry mix and sand, add one quart of Primer. More Primer may be used, but under no circumstances use less than the amounts prescribed above.


Special Gyp-Crete Instructions

In order to properly glue down wood flooring to Gyp-Crete or lightweight concrete, the surface must be primed with Titebond Concrete Primer. For this application, the Primer must be applied at a rate of 400 square feet per gallon using a mix of one-part clean water and two part Primer. Apply evenly with a squeegee, brush, roller or spray. Allow 45 minutes or more before applying a second coat. Allow to dry 24 hours before applying adhesive over the primer/sealer. For additional concerns regarding job site conditions, moisture or specific applications, call Franklin International Technical Service at 1-800-347-4583.


Cleanup

Water when wet; dried film can be scraped.


Titebond Concrete Primer is formulated specifically for use with various Franklin International flooring adhesives. While it will perform satisfactorily with other adhesives, it can be hardened or softened by the solvents in some adhesives. If there is any question about the adhesive being used in conjunction with Titebond Concrete Primer, consult Franklin International Technical Service at 1-800-347-4583 or perform the following test: Apply a small amount of concrete mixture to the surface and allow it to dry at least 3-5 days. Bond an assembly with the adhesive you intend to use and allow to set for 72 hours. Separate the assembly and inspect the glue line. If the bond is strong and the adhesive is firm, you should have no problems.
CAUTION: Do not allow eye contact. Protective splash goggles are suggested as eye protection. If eye contact occurs, flush with water for 10-15 minutes. Consult physician. Do not ingest. If ingested, do not induce vomiting. Consult physician. KEEP OUT OF THE REACH OF CHILDREN.
Part No.SizeWeight(lbs.)UPCCase UPCUnits Per PackagePackages Per Pallet
15136Gallon Jug18.2703708315136710037083151364263
  • woodworking
  • construction
  • caulk
  • flooring
  • Titebond Woodglues
  • PROVantage
  • WeatherMaster
  • Green Choice
  • Titebond Premium
  • XtremeFoam